It appears you have not yet Signed Up with our community. To Sign Up for free, please click here....



Knee & Hip Problems Message Board

  • Hip replacement disaster, long post

  • Post New Thread   Closed Thread
    Thread Tools Search this Thread
    Old 04-25-2008, 07:17 PM   #1
    chkabq
    Newbie
    (male)
     
    chkabq's Avatar
     
    Join Date: Apr 2008
    Location: Albuquerque, NM USA
    Posts: 3
    chkabq HB User
    Hip replacement disaster, long post

    My wife, who is 72, had total hip replacement surgery last July 18. When her doctor came out of the surgery room, after 3-1/2 hours, he told me that my wife’s pelvis had fractured, that she lost two liters of blood and that her blood pressure had dropped to 70/50. I was astonished, to say the least. Her doctor said that her pelvis had broken when he pounded the prosthesis in with a hammer.

    I asked him if it was a force fit. He said, “Yes.” I asked him if it was intended to be an interference fit, and again he said, “Yes.” I asked him how much of an interference. He said, “Zero to two millimeters.” He said that the hoop stress was what had broken her pelvis. I mentioned to him that “hoop stress” is an engineering term. (I am and engineer.)

    He then gave me a card that had diagrams of a hip-replacement prosthesis, but he said that it was not the one that he had used; that he had used a different one, a new one. The upper, or socket part of the prosthesis shown on the card had a section of a sphere that was to be fitted into the pelvis, but the doctor said that the one on the card was not the prosthesis that he used.

    When I got home, I went on the internet and found a hip-replacement prosthesis that did indeed require an interference fit of zero to two millimeters. The prosthesis that I found showed the ball and socket prosthesis with the socket, or upper part, having a circular cylinder part that protruded out to be inserted into a hole drilled into the pelvis, instead of a section of a sphere.

    It said that the amount of interference required varies from zero to two millimeters and depends on the degree of osteoporosis; that a pelvis that has severe osteoporosis requires two millimeters of interference, and a pelvis that has little or no osteoporosis requires zero interference. Various degrees of osteoporosis between those extremes requires an interference somewhere between zero and two millimeters. An interference fit of, say, one millimeter, requires that the hole that is bored into the pelvis should be one millimeter smaller than the diameter of the cylinder on the upper, or socket, part of the prosthesis.

    The doctor did NOT do a bone density test prior to the surgery, so he did not know the degree, if any, of any osteoporosis. My wife is very large and heavy. It is my understanding that heavy people have little if any osteoporosis. It appears to me that he just guessed about how much interference to plan for, and he guessed wrong.

    I did not make a note of the manufacturer of the prosthesis with the cylindrical part, the one that requires an interference fit of zero to two millimeters, or of the web site on which I found it. A few weeks later, I again got on the internet to find the same prosthesis, but I could not find it anywhere. Since then I have never been able to find that prosthesis or its instructions.

    I did get information that a certain prosthesis had recently been removed from the market but I did not make a note of which one. All of them that I have found since then have an upper prosthesis that has the shape of a partial sphere that must be fitted into a spherical cavity in the pelvis. And there is no mention of an interference fit of zero to two millimeters on any of these.

    If the prosthesis that the doctor used on my wife has indeed been removed from the market and all information regarding it has also been removed from internet web sites, then something has been going on.

    Today my wife had another appointment with her doctor. Before she left home, I asked her to ask him two questions: (1) What is the name of the manufacturer of the prosthesis? And (2) Why is information about the one that requires zero to two millimeters no longer to be found on the internet?

    After her appointment today, she said that she asked him about the manufacturer, and then she remembered that he had given her a card, she thinks when she saw him for the first time after her surgery. She showed me the card, and it was the same card with the same upper, or socket part of the prosthesis, the one having the spherical end. I told my wife that it was the same one that her doctor had said was NOT the one that he had used in her surgery. She said that he had told her that it IS the one that he used. She said that he said that there had been another one that had had comments made and that it had been recalled. It appears that he has changed his story.

    My wife is adamantly opposed to even talking to an attorney about this. What should I do? It has been many months since her surgery, and she still has trouble walking, even with a cane. Physical therapy seems not to help.

    Last edited by chkabq; 04-25-2008 at 08:58 PM.

     
    Sponsors Lightbulb
       
    Old 04-26-2008, 12:55 AM   #2
    legallyblondied
    Veteran
    (female)
     
    Join Date: Jun 2005
    Posts: 303
    legallyblondied HB User
    Re: Hip replacement disaster, long post

    Hi...i would contact an attorney who does malpractice and gross negligence. He definitely a defective product and he
    lied to your wife about the prosthesis he used. Find an attorney. You are a bright man and can do the research on
    the product that was taken off the market. An attorney, if he
    feels you have a good case, will take this on a contingency fee
    basis and if smart will go after the doc and the manufacturer
    of the device since they have deep pockets and will settle usually out of court. The doc may only be familiar with the one device and knew or should have known the outcome and
    also had all of the appropriate tests done bone density xrays
    etc. before any of this was done.....Karen

     
    Old 04-26-2008, 08:47 AM   #3
    chkabq
    Newbie
    (male)
     
    chkabq's Avatar
     
    Join Date: Apr 2008
    Location: Albuquerque, NM USA
    Posts: 3
    chkabq HB User
    Re: Hip replacement disaster, long post

    Thank you, Karen. I'd very much like to do that, but my wife, for some reason, does not want to. Also, my elder daughter, who is an oncologisst, is embarrassed that I would even think about doing that. She, however, doesn't know the details of what the doctor did and what he has said. I'll try to convince her, but i don't think she'll budge. Grrrrr.

    In New Mexico, there is a three-year statute of limitaions, so I have time.
    Thanks, again.
    Charles

     
    Old 04-26-2008, 12:52 PM   #4
    libloom
    Veteran
    (female)
     
    libloom's Avatar
     
    Join Date: Oct 2002
    Location: Pittsburgh PA
    Posts: 342
    libloom HB User
    Re: Hip replacement disaster, long post

    You are entitled to get a copy of the operative report, which should list the manufacturer's name. Call the hospital first thing Monday and inquire. There's usually a small fee for the report......

    A lot of time, surgeons wait until they take a look see inside to determine which prosthesis parts to use. They all try to get a good press-fit. I'm assuming your wife's was non-cemented?

    Bone density is a huge factor when deciding to have a THR....and it would make sense for the surgeons to order a density test along with all of the other pre-op tests. Unfortunately, most don't. Are you sure it wasn't the femur that cracked during insertion of the stem? That happens often.

    Good luck,
    Linda

     
    Old 04-26-2008, 02:38 PM   #5
    chkabq
    Newbie
    (male)
     
    chkabq's Avatar
     
    Join Date: Apr 2008
    Location: Albuquerque, NM USA
    Posts: 3
    chkabq HB User
    Re: Hip replacement disaster, long post

    Thanks, Linda.
    Yes, I'm sure it was not the femur that broke. Her pelvis is now held together with steel plates, bolts, and screws.

    I hadn't thought about getting a report from the hospital. I'll do that. Thanks for the suggestion.

    My main concern now is trying to convince my wife and daughter that what he did is not OK, that it was incompetence, and I want to teach him a lesson, because he has put my wife through torture, and it's not over.
    Charles

     
    Closed Thread

    Related Topics
    Thread Thread Starter Board Replies Last Post
    IDET / disc replacement eeyoretigger Back Problems 23 08-08-2011 09:01 AM
    Total Knee Replacement: Recovery - Things I wish I knew! tiredbeinsick Knee & Hip Problems 544 10-27-2009 07:04 PM
    Why I am Having Difficulty with HC Replacement? sparkles916 Addison's Disease 17 08-29-2008 07:47 PM
    Hip Replacement Surgery - I Need Moral Support kate38ca Knee & Hip Problems 76 07-06-2008 06:52 PM
    The Truth About Disc Replacement: Help! D.LYNN Back Problems 45 05-16-2007 06:38 AM
    Re: Lawsuit on Disk Replacement catnap Pain Management 2 11-01-2005 10:59 AM
    Has anyone had disc replacement? norahs Back Problems 1 07-09-2004 05:28 PM
    Disc replacement surgery nycgirl25 Back Problems 23 04-23-2004 07:12 PM




    Thread Tools Search this Thread
    Search this Thread:

    Advanced Search

    Posting Rules
    You may not post new threads
    You may not post replies
    You may not post attachments
    You may not edit your posts

    BB code is On
    Smilies are On
    [IMG] code is Off
    HTML code is Off
    Trackbacks are Off
    Pingbacks are Off
    Refbacks are Off




    Sign Up Today!

    Ask our community of thousands of members your health questions, and learn from others experiences. Join the conversation!

    I want my free account

    All times are GMT -7. The time now is 07:15 PM.





    © 2021 MH Sub I, LLC dba Internet Brands. All rights reserved.
    Do not copy or redistribute in any form!